How To Put A Jump Start On A Battery To Avoid Explosion, Gnewscar – Battery worn out and unable to start a car engine? As a temporary solution, jumper (jump start) techniques are often used. In simple terms, this action is carried out to transfer electricity from another battery to a worn-out car battery and is used to start the engine. The tool is called a jumper cable.
However, to do so can not be arbitrary. Many lay people who originate connecting careless batteries with other car batteries without technique. If the wrong installation, the result can be shorted or even explode.
How to Install the Jump Start
- Make sure that the engine won’t turn on because of the battery. For example, by turning on the light: if it’s dim, the battery might be worn out; if it’s bright, then it’s not a matter of the battery.
- Once you are sure the battery is completely stunned, bring other cars that are still normal in a face to face position, about 30 cm bumper-to-bumper if possible. If the car is automatic, make sure the transmission lever is in the “park” position, if the manual transmission car is in the “neutral” position. Handbrake must be fully installed.
- Wear rubber gloves, find positive (+) and negative (-) poles on the batteries of both cars. When the poles are colored, red is positive and black is negative.
- Take the jumper cable, attach the positive jumper cable clamp (red) to the positive pole of the normal car battery, and the other end of the positive pole of the damaged car battery.
- Install the negative (black) jumper cable clamp in the negative terminal of the normal car battery. CAUTION, this cable can now be filled with stun. Do not touch the cable clip to the body or other parts of the car.
- Pinch the other end of the black jumper cable to the metal of the car near the engine, preferably on the battery support bolts that connect to the chassis. If this is not possible, pin it to a shiny, unpainted metal plate in the engine room, but away from moving parts such as a fan belt.
- Check that there are no wires dangling in the direction of moving objects in the engine room.
- After it is believed to be safe, turn on a normal car for 1-2 minutes. Step on the gas slowly to slightly increase engine speed.
- Turn on a damaged car, it might need more than once, but don’t repeat it up to four or more times. If it fails the first try, you may need another ground clamp for the negative cable, and let the normal car live for five minutes before the damaged car is turned on. Or for a last resort, the end of the negative cable is clipped to the negative pole of the damaged battery, but risks splashing on the hydrogen gas coming out of the battery. If not yet alive, it’s better to tow the car.
- If the engine starts successfully, leave it for five minutes slightly above idle by pressing the gas lightly, after that let it run 20 minutes in the idle position (without stepping on the gas). This procedure should be enough to fill the battery. If after that the car fails to start again, you should replace it with a new battery.
Jumper (jump start) technique is one solution when the car is difficult to start because I’m already weak. This is a way to conduct electricity, from a car whose battery is good to a car whose battery is weak (cannot be started).
Tool for jumping only using jumper cables and cars with good battery condition. However, make sure the cable purchased has a large size and is able to withstand large electric currents.
Warning:
1. Do not let the battery positive terminal connected to metal objects. This will cause sparks. The problem is, sparks near the cell battery are very dangerous. Hydrogen gas produced during normal battery operation can cause explosions and serious burns. When working close to a battery, do not let the metal work tools connected to the positive and negative terminals.
2. Keep all fires, including cigarettes and sparks, away from the open cell battery.
3. Do not jumper with a frozen battery or a battery with very low liquid. “It’s also dangerous, has the potential to explode and cause serious injury,” Tunjung said.
4. Connect the negative cable to a good ground point and away from the battery. Make sure you use the best Jumper Staters
5. Keep the jumper cable away from moving components (for example: V-belts, fan motors, etc.).